Tête de coupe spirale Sheartak pour raboteuse General 30-125CE de 15 pouces
Chaque plaquette carbure possède 4 arêtes indexables. Les plaquettes en carbure sont légèrement inclinées par rapport à l'alimentation de la planche, ce qui génère une coupe en cisaillement, élimine l'arrachement et laisse une finition de surface brillante sur les bois tendres, les bois durs et les panneaux manufacturés. Cela réduit considérablement le bruit de fonctionnement.
Il suffit de faire pivoter le bord de 90 degrés s'il est émoussé ou ébréché et vous aurez un nouveau bord tranchant. Jetez les plaquettes en carbure bon marché seulement lorsque les quatre bords sont affectés et qu'il n'est pas nécessaire d'aiguiser les plaquettes. Les têtes de coupe en spirale Sheartak réduisent les trois quarts de votre travail de ponçage et consomment moins d'énergie. Ces têtes de coupe enlèvent de petits copeaux de manière décalée, ce qui évite l'encrassement de la hotte, améliorant ainsi l'extraction de la poussière. Les têtes de coupe en spirale Sheartak peuvent vous faire récupérer votre investissement initial en un rien de temps.
Le kit de tête de coupe en spirale comprend :
* Bloc de coupe en acier allié à haute résistance.
* Deux roulements étanches NSK japonais de qualité supérieure.
* 52 / 75 / 80 plaquettes en carbure installées.
* 5 plaquettes en carbure supplémentaires.
* 5 vis supplémentaires.
* 1 clé
* Garantie d'un an pour le bloc de coupe.
Do I need to replace the original bearings?
If the bearings in your machine are in good condition, they can be reused by carefully removing them with a bearing or pulley puller. However, if the bearings are tightly pressed onto the shaft, removal may cause damage. To minimize this risk, we recommend replacing old bearings with our greased and sealed bearings, designed for long-lasting performance. For a smooth upgrade, we suggest adding the bearings to your shopping cart before completing your purchase.
We provide premium bearings from NSK, SKF, NTN, FAG, Timken. They are renowned for their high quality and performance, designed to provide durability and reliability in various applications
Do I need to to Add a Few Boxes of Carbide Inserts
We provide 5 carbide inserts and 5 screws as spare parts. However, many of our customers choose to purchase additional boxes, as the shipping costs for separate purchases can make it less economical.
Do I need a Torque Wrench?
To securely lock the carbide inserts, we recommend applying a torque of 48 to 52 Pound-Inches (or 5.42 to 5.88 Newton-Meters). (Note: 1 Newton-Meter is equal to 8.851 Pound-Inches, and 1 Pound-Inch is approximately 0.113 Newton-Meters.) It is crucial not to apply excessive torque, as this could cause the carbide inserts to crack or explode. On the other hand, using too little torque may result in the inserts not being properly secured, which could lead to cracks, shattering, or uneven height on the cutter block, causing ridges or lines on the board.
If one person is responsible for maintaining the machine, they can typically apply the same torque consistently without a torque wrench. However, when multiple people are involved in machine maintenance, ensuring uniform torque application can be challenging. For consistency and peace of mind, we recommend using a torque wrench.
What kind of steel the cutter block is made of?
The cutter block is constructed using GB/T 40Cr, a structural alloy steel of the same caliber as ASTM grade 5140, AISI 5140, SAE 5140, DIN 41Cr4, BS 41Cr4, JIS SCr440, and EN 41Cr4.The primary components of this steel are as follows: carbon (C) at a range of 0.37-0.44%, silicon (Si) between 0.17-0.37%, manganese (Mn) within 0.50-0.80%, and chromium (Cr) from 0.80-1.10%.
In terms of physical properties, this steel exhibits a tensile strength range of 115-234σb/MPa, a yield strength of 2σ 0.2 ≥/MPa, and an elongation capacity of 65 δ5≥ (%). It also has a HBS range of 123-321 and a HRC rating of 30.
This alloy steel is frequently utilized in low to moderately stressed components for machines, engines, and vehicles.
