piral Cutterhead for GRIZZLY G1018 8" Jointer (Approx. 20 Years Old)
Many woodworkers are now upgrading their older jointers and planers with spiral cutterheads—and for good reasons:
-
Smoother Finish, No Tear-Out
The blades are set at an angle and cut in a spiral pattern. This creates a shearing action that leaves a smooth, shiny surface—even on difficult hardwood. It works much better than straight blades.
-
Much Quieter
Because the blades cut one at a time in a staggered pattern, the machine runs more quietly.
-
Lasts Over 10 Times Longer
The small blades (inserts) are made of tough tungsten carbide. Each one has 4 sharp edges. When one edge gets dull, just rotate it to the next side.
-
Easy to Change Blades
All inserts are the same and very precise. Just loosen the screw, turn the insert 90 degrees, and tighten—it only takes a few minutes.
-
Better Dust Collection
Spiral heads make smaller, thinner chips that are easier to collect with your dust system.
-
Saves Time and Money
You’ll get a smooth finish with less or no sanding. No sharpening needed. The cutterhead quickly pays for itself.
What’s Included in the Kit:
Do I need to replace the original bearings?
If the bearings in your machine are in good condition, they can be reused by carefully removing them with a bearing or pulley puller. However, if the bearings are tightly pressed onto the shaft, removal may cause damage. To minimize this risk, we recommend replacing old bearings with our greased and sealed bearings, designed for long-lasting performance. For a smooth upgrade, we suggest adding the bearings to your shopping cart before completing your purchase.
We provide premium bearings from NSK, SKF, NTN, FAG, Timken. They are renowned for their high quality and performance, designed to provide durability and reliability in various applications
If you add the bearings to your order, we will preinstall them for you when premounting is possible, saving you the hassle of doing it yourself.
Do I need to to Add a Few Boxes of Carbide Inserts
We provide 5 carbide inserts and 5 screws as spare parts. However, many of our customers choose to purchase additional boxes, as the shipping costs for separate purchases can make it less economical.
Do I need a Torque Wrench?
To securely lock the carbide inserts, we recommend applying a torque of 48 to 52 Pound-Inches (or 5.42 to 5.88 Newton-Meters). (Note: 1 Newton-Meter is equal to 8.851 Pound-Inches, and 1 Pound-Inch is approximately 0.113 Newton-Meters.) It is crucial not to apply excessive torque, as this could cause the carbide inserts to crack or explode. On the other hand, using too little torque may result in the inserts not being properly secured, which could lead to cracks, shattering, or uneven height on the cutter block, causing ridges or lines on the board.
If one person is responsible for maintaining the machine, they can typically apply the same torque consistently without a torque wrench. However, when multiple people are involved in machine maintenance, ensuring uniform torque application can be challenging. For consistency and peace of mind, we recommend using a torque wrench.
What kind of steel the cutter block is made of?
The cutter block is constructed using GB/T 40Cr, a structural alloy steel of the same caliber as ASTM grade 5140, AISI 5140, SAE 5140, DIN 41Cr4, BS 41Cr4, JIS SCr440, and EN 41Cr4.The primary components of this steel are as follows: carbon (C) at a range of 0.37-0.44%, silicon (Si) between 0.17-0.37%, manganese (Mn) within 0.50-0.80%, and chromium (Cr) from 0.80-1.10%.
In terms of physical properties, this steel exhibits a tensile strength range of 115-234σb/MPa, a yield strength of 2σ 0.2 ≥/MPa, and an elongation capacity of 65 δ5≥ (%). It also has a HBS range of 123-321 and a HRC rating of 30.
This alloy steel is frequently utilized in low to moderately stressed components for machines, engines, and vehicles.
