Spiral Cutterhead for Holzmann DHM330 Thickness Planer 40 Carbide Blades

Upgrade your Holzmann DHM330 with the Sheartak Spiral Cutterhead, designed for superior performance and efficiency. Equipped with 40 high-quality carbide inserts, each featuring 4 indexable edges, this cutterhead delivers exceptional results on softwood and highly figured hardwood. The angled inserts create a shear cut, eliminating tear-out and producing a smooth, high-quality surface finish while significantly reducing noise levels.

When an edge becomes dull or nicked, simply rotate the insert a quarter turn to access a fresh, sharp edge. Replace the cost-effective carbide inserts only after all four edges are worn, eliminating the need for sharpening and minimizing downtime. The spiral design reduces power consumption, cuts sanding time by up to 75%, and improves dust extraction by preventing clogs at the hood port. The Sheartak Spiral Cutterhead is a smart investment that pays for itself quickly through enhanced efficiency and reduced maintenance.

Kit Includes:

• High-tensile alloy steel cutter block

• 40 pre-installed carbide inserts

• 5 extra carbide inserts and 5 screws as spares

• 1 pair of premium sealed bearings

• 1 wrench for easy maintenance

Do I need to replace the original bearings?
If the bearings in your machine are in good condition, they can be reused by carefully removing them with a bearing or pulley puller. However, if the bearings are tightly pressed onto the shaft, removal may cause damage. To minimize this risk, we recommend replacing old bearings with our greased and sealed bearings, designed for long-lasting performance. For a smooth upgrade, we suggest adding the bearings to your shopping cart before completing your purchase.
We provide premium bearings from NSK, SKF, NTN, FAG, Timken. They are renowned for their high quality and performance, designed to provide durability and reliability in various applications
If you add the bearings to your order, we will preinstall them for you when premounting is possible, saving you the hassle of doing it yourself.

Do I need to to Add a Few Boxes of Carbide Inserts
We provide 5 carbide inserts and 5 screws as spare parts. However, many of our customers choose to purchase additional boxes, as the shipping costs for separate purchases can make it less economical.

Do I need a Torque Wrench?
To securely lock the carbide inserts, we recommend applying a torque of 48 to 52 Pound-Inches (or 5.42 to 5.88 Newton-Meters). (Note: 1 Newton-Meter is equal to 8.851 Pound-Inches, and 1 Pound-Inch is approximately 0.113 Newton-Meters.) It is crucial not to apply excessive torque, as this could cause the carbide inserts to crack or explode. On the other hand, using too little torque may result in the inserts not being properly secured, which could lead to cracks, shattering, or uneven height on the cutter block, causing ridges or lines on the board.
If one person is responsible for maintaining the machine, they can typically apply the same torque consistently without a torque wrench. However, when multiple people are involved in machine maintenance, ensuring uniform torque application can be challenging. For consistency and peace of mind, we recommend using a torque wrench.

What kind of steel the cutter block is made of?
The cutter block is constructed using GB/T 40Cr, a structural alloy steel of the same caliber as ASTM grade 5140, AISI 5140, SAE 5140, DIN 41Cr4, BS 41Cr4, JIS SCr440, and EN 41Cr4.The primary components of this steel are as follows: carbon (C) at a range of 0.37-0.44%, silicon (Si) between 0.17-0.37%, manganese (Mn) within 0.50-0.80%, and chromium (Cr) from 0.80-1.10%.
In terms of physical properties, this steel exhibits a tensile strength range of 115-234σb/MPa, a yield strength of 2σ 0.2 ≥/MPa, and an elongation capacity of 65 δ5≥ (%). It also has a HBS range of 123-321 and a HRC rating of 30.
This alloy steel is frequently utilized in low to moderately stressed components for machines, engines, and vehicles.